基本性質/ TYPICAL CHARACTERISTICS
型式/ Type : 弱酸型陽離子交換樹脂/Weak acid cation exchange resin
結構/ Matrix structure : 巨孔狀交叉鍵結聚苯乙烯/
Macroporous cross1inked polystyrene
官能基/ Functional group : Iminodiacetic
物理型式/ Physical form : 含水球狀/ Moist spherical beads
離子型式/ Ionic as shipped : 鈉/ Sodium
粒徑分布/ Screen size USS(wet) : 16 to 50
粒徑大小/ Particle size : 0.3 to 1.2 mm
總交換容量/Total Exc. Capacity : 1.8 meq/ml (H+)
膨脹系數/ Swelling (approx.) : H+ → Na+ 20%
含水份/ Moisture : 45-50%
pH 作范圍/ Suitable pH range : 0 to 14
溶解率/Solubility : 不溶解于任何溶劑/ Insoluble in common solvents
逆洗沉降密度/Backwash settled density : 0.72 to 0.79 g/ml

建議操作條件/ OPERATING CONDITIONS
操作溫度/ Max .Operating Temperature : 70oC
流速/ Service flow : 10 – 30 BV/hr
逆洗膨脹空間/Backwash expansio ace : 50 to 70%
逆洗流速/ Backwash expansion flow : 8-10 BV/hr
再生/ Regeneration
酸濃度/ Concentration of acid : 5 - 8%
流速/ Flow rate : 3 – 4 BV/hr
再生酸藥劑量/ Regeneration quantity: 150-200 g/lit of HCl
:200-250g/lit of H2SO4
慢洗流速/ Rinse flow rate : 3 – 4 BV/hr
若需要轉成Na離子/ Conversion to sodium form if required
濃度/ Concentration : 2-4%
流速/ Flow : 4 BV/hr
鹽藥量/ NaOH quantity : 50-150 g/lit
慢洗流速/ Rinse flow rate : 3 – 4 BV/hr

應用附注/ APPLICATION NOTE
金屬離子的選擇性是依據進流液的pH 而決定在某些的pH 范圍內, 交換容量會很嚴重的下降.
zyx的除銅pH : 3 - 4
Effective pH for copper removal
zyx的除鎳pH : 3 - 5
Effective pH for nickel removal
zyx的除鐵pH : 2 - 4
Effective pH for iron removal
zyx的除鉛pH : 2 以上
Effective pH for lead removal
zyx的除錳pH : 4 以上
Effective pH for manganese
選擇性的順序如下:
Order of selectivity is as follows
Cu > Pb > Ni > Zn > Co > Cd > Fe+3 > Mn > Mg > Ca >> Na
再生藥劑的選擇可用鹽酸或硫。對于除銅應用, 建議用硫酸! 建議用鹼NaOH 再生將樹脂轉換成Na 型, 并將pH 變成原來的進水條件。