柔軟型輕觸開關6×6×5mm 相關信息由 東莞市品贊電子科技有限公司提供。如需了解更詳細的 柔軟型輕觸開關6×6×5mm 的信息，請點擊 http://m.qnon.net/b2b/dgpz.html 查看 東莞市品贊電子科技有限公司 的詳細聯系方式。
|
6.PERFORMANCE性能 6.1 Electrical電氣 |
||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
6.1.1. Contact Resistance 接觸電阻 |
Applying astatic load twice the actuating force to the center of the stem,measurements shall be made with a 1 kHz small-current contact resistance meter. 用兩倍的動作力作靜負載施加于按鈕的中心,并用1千赫 小電流接觸電阻儀測量 |
100 m ohm max. |
|
6.1.2. Insulation Resistance 絕緣電阻 |
Measurements shall be made following application of DC100V potintial across terminals and across terminals and frame for one minute. 在端子與端子之間,端子與外殼之間施加DC100V,一分鐘 |
100 M ohm min. |
|
6.1.3. Dielectric witstanding voltage 電氣耐壓 |
AC250V(50Hz or60Hz) shall be applied across terminals and across terminals and frame for one minute. 在端子與端子之間,端子與外殼之間施加AC250V(50HZ-60HZ) |
There shall be no breakdown. 沒有擊穿 |
|
6.1.4. Bounce 抖動 |
Lightly striking the center of the stem at a rate encountered in normal use (3 to 4 operations per sec.), Bounce shall be tested at “ON”and “OFF”. 在正常使用中(以每秒3-4次周期)輕輕地在手柄中心加力,在通 與斷瞬間測試抖動  |
5 m sec max. |
|
6.2Mechanical機械特性 |
||
| Item項目 | Test Condition 試驗條件 | Requirements 規 格 |
|
6.2.1. Actuating Force 動作力 |
Placing the switch such that the direction of switch operation is vertical and then gradually increasing the load applied to the center of the stem, the maximum load required for the stem to come to a stop shall be measured. 開關的動作方向?yàn)榇怪狈胖瞄_(kāi)關向推柄中心逐漸地 增加負荷直到推柄停止時所測量的{zd0}負荷 |
160 ± 50 gf or 250 ± 50 gf or 300 ± 50 gf |
|
6.2.2. Travel 行程 |
Placing the switch such that the direction of switch operation is vertical and then applying a static load twice the actuating force to the center of the stem,the travel distance for the stem to come to a stop shall be measured. 開關的動作方向?yàn)榇怪狈胖瞄_(kāi)關, 并以雙倍動作力的靜負荷作用推柄中心,測量推柄從 開始到停止的行程距離 |
0.25 ± 0.1mm |
|
6.2.3. Return Force 返回力 |
The sample switch is installed such that the direction of switch operation is vertical and, upon depression of the stem in its center the whole travel distance ,the force of the stem to return to its free position shall be measured. 開關的動作方向?yàn)榇怪狈胖瞄_(kāi)關, 在已有行程的推柄中心向上減小壓力,推柄回到自由位置 時所測量到的力 |
45 gf min |
|
6.2.4. Stop Strength 靜止強度 |
Placing the switch such that the direction of switch operation is vertical,a static load of 3 kgf shall be applied in the direction of stem operation for a period of 60 seconds. 開關的動作方向?yàn)榇怪狈胖瞄_(kāi)關,在推柄動作方向施加 3KG的靜負荷,60秒時間 |
There shall be no sign of damage mechanically and electrically. 無機械的和電氣的損傷跡象 |
|
6.2.5. Stem Strength 推柄的強度 |
Placing the switch such that the direction of switch operation is vertical, the maximum force to withstand a pull applied oppsite to the direction of stem operation shall be measured. 開關的動作方向?yàn)榇怪狈胖瞄_(kāi)關, 從推柄動作方向反方向施加拉力所測量到的{zd0}承受力 |
3 kgf |
| 6.3Environmental環境 | ||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
6.3.1. Resistance to Low Temperatures 耐低溫 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐低溫試驗,測試前在正常溫度和濕 度條件下放置1小時
|
Item 6.1 Item 6. 2.1 Item 6.2.2 |
|
6.3.2. Heat Resistance 耐熱 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐熱試驗,測試前在正常溫度和濕度 條件下放置1小時 (1)Temperature: 80±2℃ 溫 度 (2) Time: 96 hours 時 間 |
Item 6.1 Item 6. 2.1 Item 6.2.2 |
|
6.3.3. Moisture Resistance 耐潮濕 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐潮濕試驗,測試前在正常溫度和濕度 條件下放置1小時
|
Contact resistance: 500 m ohm max接觸電阻 Insulation resistance 10 M ohm min. 絕緣電阻 Item 6.1.3 Item 6.2.1 Item 6.2.2 |
| 6.3Environmental環境 | ||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
6.3.1. Resistance to Low Temperatures 耐低溫 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐低溫試驗,測試前在正常溫度和濕度 條件下放置1小時 (1) Temperature: -30±2℃ 溫 度 (2) Time: 96 hours 時 間 (3) Water drops shall be removed. 擦除水珠 |
Item 6.1 Item 6. 2.1 Item 6.2.2 |
|
6.3.2. Heat Resistance 耐熱 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐熱試驗,測試前在正常溫度和濕度 條件下放置1小時 (1)Temperature: 80±2℃ 溫 度 (2) Time: 96 hours 時 間 |
Item 6.1 Item 6. 2.1 Item 6.2.2 |
|
6.3.3. Moisture Resistance 耐潮濕 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 樣品按下列條件進行耐潮濕試驗,測試前在正常溫度 和濕度條件下放置1小時 (1) Temperature: 60±2℃ 溫度 (2) Relative humidity: 90 to 95% 相對濕度 (3) Time: 96 hours 時 間 (4) Water drops shall be removed. 擦除水珠 |
Contact resistance:500 m ohm max接觸電阻 Insulation resistance 10 M ohm min. 絕緣電阻 Item 6.1.3 Item 6.2.1 Item 6.2.2 |
| 6.4Endurance耐久性 | ||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
6.4.1. Operating Life 動作壽命 |
Measurements shall be made following the test set forth below: 按下列條件 進行壽命試驗 (1)DC 5V 5mA resistive load. DC 5V 5mA 阻性負載 (2)Rate of operation:2 to 3 operations per second 動作頻率:2-3次/每秒 (3)Depression: 180 gf 減壓力 (4)Cycles of operation: 5×104 cycles 動作次數: 5×104次 |
Contact resistance: 1 Ω max. 接觸電阻 Insulation resistance : 10 M ohm min. 絕緣電阻 Actuating force: 動作力 + 30 %or- 30%of initial force. ±30%初始動作力 Item 6.1.3 tem 6. 2.2 |
|
6.4.2. Vibration Resistance 耐振動 |
Measurements shall be made following the test set forth below: 按下列條件進行抗振動試驗 (1)Range of oscillation:10 to 55Hz 頻率范圍 (2)Amplitude,pk-to-pk:1.5 mm 振幅: 峰-峰1.5mm (3)Cycle of sweep: 10-55-10Hz in one minute,approx. 掃描周期: 10-55-10Hz約一分鐘內 (4)Mode of sweep :Logarithmically sweep or uniform sweep. 掃描方式:對數掃描式恒定掃描 (1) Direction of oscillation: 振動方向 Three mutually perpendicular directions,including the directionof stem travel. 3個相互垂直方向,包括推柄行程方向 (2) Duration of testing: 持續時間 2 hours each ,for a total of 6hours.每方向2小時.共6小時 |
Item 6.1 Item 6.2.1 Item 6.2.2 |
|
6.4.3. Impact Shock Resistance 抗沖擊 |
Measurements shall be made following the test set forth below: 按下列條件進行沖擊試驗 (1)Acceleration:80g 加速度 (2)Cycles of test :3 cycles each in 6directions, for a total of 18cycles 試驗次數：每個方向3次,6個方向共18次 |
Item 6.1 Item 6.2.1 Item 6.2.2 |
| 7. Environmental Endurance 環境耐久性 | ||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
7.1. High Temperature Cycling 高溫循環 |
Foeeowing ten cycles of high temperature test .Saupee shall be Place in Normae temperature and humidity Conditious for one hour before measurements are made. During this test, water drops shall be removed. 樣品按下列條件進行高低溫循環試驗, 測試前在正常溫度和溫度條件下放置1小時,除去水珠 (1) Temperature(溫度)：-30°~80℃ (2) Cycling(周期)：Ten cycles (10個周期) 
|
Item 6.1 Item 6. 2.1 Item 6.2.2 |
|
7.2 Moisture Resistance 耐潮濕 |
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hourbefore measurements are made: 樣品按下列條件進行耐潮濕試驗, 測試前在正常溫度和濕度條件下放置1小時 (1) Temperature: 85±2℃ 溫度 (2)Relative humidity: 80 to 85% 相對濕度 (3) Time: 500 hours 時 間 (3) Water drops shall be removed. 擦除水珠 |
Contact resistance:50 m ohm max 接觸電阻 Insulation resistance 10 M ohm min. 絕緣電阻 Item 6.1.3 Item 6.2.1 Item 6.2.2 |
| 8.Use Endurance 使用耐久性 | ||
| Item項目 | Test Condition測試條件 | Requirements要求 |
|
8.1 Solderability 焊接性 |
Oven Temperature:235℃±5℃，Time: 5S±1S 錫爐溫度：235℃±5℃ 時間:5秒±1秒 |
Tin Area:90％ 焊接面積90％以上 |
|
8.2 patience high temperature 焊接耐熱性 |
Preheat: Temperature on the copper foil surface should reach 180℃, 2±0.3 minutes after The P.W.B entered into the soldering equipment 預熱：在P.W.B(印刷線路板)進入焊接設備后， 2±0.3分鐘內銅箔表面要達到180℃ Soldering heat: Temperature on the copper foil surface should reach the peak temperature of 260℃ within 5 seconds after the P.B.W entered into soldering heat zone. 焊接溫度： 在P.W.B(印刷線路板)進入焊接溫區5秒內， 銅箔表面達到峰值溫度260℃ 
|
表面無起泡,變型 Surface of plastics don’t frothed And formed |
